Yamaha YP125R Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 498

background image

ENGINE (YP125R)

3-9

15.Install:

• Upper panel

Refer to “GENERAL CHASSIS” on page 4-1.

EAS37P1090

ADJUSTING THE THROTTLE CABLE FREE
PLAY

1. Check:

• Throttle cable free play “a”

Out of specification

→

Adjust.

2. Adjust:

• Throttle cable free play

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Slide back the rubber cover “1”.
b. Loosen the locknut “2”.
c. Turn the adjusting nut “3” in direction “a” or “b”

until the specified throttle cable free play is
obtained.

d. Tighten the locknut.
e. Slide the rubber cover to its original position.

WARNING

EWA12910

After adjusting the throttle cable free play,
start the engine and turn the handlebar to the
right and to the left to ensure that this does
not cause the engine idling speed to change.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS37P1091

CHECKING THE SPARK PLUG

1. Disconnect:

• Spark plug cap “1”

2. Remove:

• Spark plug

NOTICE

ECA13330

Before removing the spark plug, blow away
any dirt accumulated in the spark plug well
with compressed air to prevent it from falling
into the cylinder.

3. Check:

• Spark plug type

Incorrect

→

Change.

4. Check:

• Electrode “1”

Damage/wear

→

Replace the spark plug.

• Insulator “2”

Abnormal color

→

Replace the spark plug.

Normal color is medium-to-light tan.

5. Clean:

• Spark plug

(with a spark plug cleaner or wire brush)

6. Measure:

• Spark plug gap “a”

(with a wire thickness gauge)
Out of specification

→

Regap.

Throttle cable free play

3.0–5.0 mm (0.12–0.20 in)

Direction “a”

Throttle cable free play is increased.

Direction “b”

Throttle cable free play is decreased.

a

1

b

a

3

2

Manufacturer/model

NGK/CPR9EA-9

Spark plug gap

0.8–0.9 mm (0.031–0.035 in)

1

«
...
134
135
136
137
138
...
»

Содержание YP125R



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP125R

Бренд: A-TO Страницы: 148

Бренд: Xootr Страницы: 2

Бренд: LOGO SILVER Страницы: 20

Allstate Cruisaire 1964

Бренд: PIAGGIO Страницы: 40

Бренд: Rascal Страницы: 32

Бренд: Easy Wheels Страницы: 21

Бренд: Pride Mobility Страницы: 34

electric motor scooter

Бренд: ZEV Страницы: 20

Бренд: UFREE SCOOTER Страницы: 11

Бренд: Manta Страницы: 20

COMET EU-H1-COMT

Бренд: Hover-1 Страницы: 31

Бренд: Manhattan Страницы: 16

Бренд: BOWHEAD Страницы: 38

Бренд: gio Страницы: 14

Бренд: gio Страницы: 18

Бренд: EzFold Страницы: 14

Бренд: Dietz Страницы: 60

Бренд: e-TWOW Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды