Yamaha YP125R Скачать руководство пользователя | Manualshive

Страница: 11 / 498

background image

FEATURES

1-2

EAS20170

FEATURES

EAS37P1140

OUTLINE OF THE FI SYSTEM

The main function of a fuel supply system is to provide fuel to the combustion chamber at the optimum
air-fuel ratio in accordance with the engine operating conditions and the atmospheric temperature. In
the conventional carburetor system, the air-fuel ratio of the mixture that is supplied to the combustion
chamber is created by the volume of the intake air and the fuel that is metered by the jet used in the
respective carburetor.
Despite the same volume of intake air, the fuel volume requirement varies with the engine operating
conditions, such as acceleration, deceleration, or operating under a heavy load. Carburetors that meter
the fuel through the use of jets have been provided with various auxiliary devices, so that an optimum
air-fuel ratio can be achieved to accommodate the constant changes in the operating conditions of the
engine.
As the requirements for the engine to deliver more performance and cleaner exhaust gases increase,
it becomes necessary to control the air-fuel ratio in a more precise and finely tuned manner. To accom-
modate this need, this model has adopted an electronically controlled fuel injection (FI) system, in place
of the conventional carburetor system. This system can achieve an optimum air-fuel ratio required by
the engine at all times by using a microprocessor that regulates the fuel injection volume according to
the engine operating conditions detected by various sensors.
The adoption of the FI system has resulted in a highly precise fuel supply, improved engine response,
better fuel economy, and reduced exhaust emissions.

1

10

7,8,9

11

12

16

14 13

15

6

5

3

2

4

1. Lean angle sensor
2. Air temperature sensor
3. ECU (engine control unit)
4. Engine trouble warning light
5. Ignition coil
6. Fuel injector
7. Intake air pressure sensor
8. Throttle position sensor
9. ISC (idle speed control) unit
10. Intake air temperature sensor
11. Crankshaft position sensor
12. O

2

sensor

13. Coolant temperature sensor
14. Spark plug
15. Fuel pump
16. Speed sensor

«
...
9
10
11
12
13
...
»

Содержание YP125R



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP125R

Бренд: Honda Страницы: 114

Бренд: Razor Страницы: 32

Бренд: Hiboy Страницы: 10

Бренд: Daymak Страницы: 32

Бренд: Huffy Страницы: 12

Бренд: CareCo Страницы: 23

Бренд: CareCo Страницы: 32

ROCKRIDER E-ST500

Бренд: Decathlon Страницы: 52

Бренд: CITY BOSS Страницы: 16

Бренд: EZee Life Страницы: 12

Бренд: EZee Life Страницы: 26

Бренд: Motus Страницы: 20

Бренд: Motus Страницы: 20

Бренд: Motus Страницы: 50

Бренд: Motus Страницы: 52

Бренд: Motus Страницы: 74

Бренд: Landlex Страницы: 10

Бренд: Hyper Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды