Yamaha YP125R Скачать руководство пользователя

Страница: 481 / 498

ELECTRICAL COMPONENTS

8-84

b. Measure the crankshaft position sensor re-

sistance.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS28130

CHECKING THE LEAN ANGLE SENSOR

1. Remove:

• Lean angle sensor

2. Check:

• Lean angle sensor output voltage

Out of specification

→

Replace.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the test harness-lean angle sensor

(6P) between the lean angle sensor and wire
harness.

b. Connect the pocket tester (DC 20 V) to the

test harness-lean angle sensor (6P).

c. Set the main switch to “ON”.
d. Turn the lean angle sensor 45°.
e. Measure the lean angle sensor output volt-

age.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS28940

CHECKING THE STARTER MOTOR
OPERATION

1. Check:

• Starter motor operation

Does not operate

→

Perform the electric

starting system troubleshooting, starting with
step 4.
Refer to “TROUBLESHOOTING” on page
8-9.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the positive battery terminal “1” and

starter motor lead “2” with a jumper lead “3”.

WARNING

EWA13810

• A wire that is used as a jumper lead must

have at least the same capacity of the bat-
tery lead, otherwise the jumper lead may
burn.

• This check is likely to produce sparks,

therefore, make sure no flammable gas or
fluid is in the vicinity.

b. Check the starter motor operation.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

red “1”

• Negative tester probe

→

white “2”

Lean angle sensor output voltage

Less than 45°: 0.4–1.4 V
More than 45°: 3.7–4.4 V

Test harness-lean angle sensor
(6P)

90890-03209

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

yellow/green “1”

• Negative tester probe

→

gray/black “2”

R Y

G Gy

45˚

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды