manualshive.com logo in svg

Yamaha YP125R, Руководство по обслуживанию

Скутер Yamaha YP125R - надежный и стильный транспорт для городских поездок. Чтобы правильно ухаживать за ним, важно иметь Owner's Manual. Скачайте бесплатно руководство по эксплуатации на manualshive.com и наслаждайтесь комфортом и удобством скутера Yamaha YP125R.

Поделиться
Скачать
background image

CHASSIS

3-41

WARNING

EWA37P1007

After extensive tests, the tires listed below 
have been approved by Yamaha Motor Es-
paña, S.A. for this model. The front and rear 
tires should always be by the same manufac-
turer and of the same design. No guarantee 
concerning handling characteristics can be 
given if a tire combination other than one ap-
proved by Yamaha is used on this vehicle.

WARNING

EWA13210

New tires have a relatively low grip on the 
road surface until they have been slightly 
worn. Therefore, approximately 100 km 
should be traveled at normal speed before 
any high-speed riding is done.

TIP

For tires with a direction of rotation mark “1”:
Install the tire with the mark pointing in the direc-
tion of wheel rotation.

EAS21670

CHECKING THE WHEELS

The following procedure applies to both of the 
wheels.

1. Check:

• Wheel

Damage/out-of-round 

→

 Replace.

WARNING

EWA13260

Never attempt to make any repairs to the 
wheel.

TIP

After a tire or wheel has been changed or re-
placed, always balance the wheel.

EAS21690

CHECKING AND LUBRICATING THE 
CABLES

The following procedure applies to all of the in-
ner and outer cables.

WARNING

EWA37P1008

A damaged outer cable may cause the cable 
to corrode and interfere with its movement. 
Replace damaged outer cable and inner ca-
bles as soon as possible.

1. Check:

• Outer cable

Damage 

→

 Replace.

2. Check:

• Cable operation

Rough movement 

→

 Lubricate.

TIP

Hold the cable end upright and pour a few drops 
of lubricant into the cable sheath or use a suit-
able lubricating device.

EAS21700

LUBRICATING THE LEVERS

Lubricate the pivoting points and metal-to-metal 
moving parts of the levers.

EAS21720

LUBRICATING THE SIDESTAND

Lubricate the pivoting point and metal-to-metal 
moving parts of the sidestand.

 

Front tire

Size

120/70–15 M/C 56P (PIRELLI)
120/70–15 M/C 56S (MICHELIN)

Manufacturer/model

MICHELIN/GOLD STANDARD
PIRELLI/GTS23

 

Rear tire

Size

140/70–14 M/C 68P (PIRELLI)
140/70–14 M/C 68S (MICHELIN)

Manufacturer/model

MICHELIN/GOLD STANDARD
PIRELLI/GTS24

 

Recommended lubricant

Engine oil or a suitable cable lu-
bricant

 

Recommended lubricant

Silicone grease

 

Recommended lubricant

Lithium-soap-based grease

Содержание YP125R



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP125R

Stiga 75-1118-XX Assembly Instructions Manual preview
75-1118-XX
Бренд: Stiga Страницы: 12
Sparco SEM1 User Manual preview
SEM1
Бренд: Sparco Страницы: 100
Afikim Breeze S3 User Manual preview
Breeze S3
Бренд: Afikim Страницы: 40
Lambretta V50 Special Assembly Manual preview
V50 Special
Бренд: Lambretta Страницы: 6
E Rider City 30 User Manual preview
City 30
Бренд: E Rider Страницы: 8
Hudora 14240 Instructions On Assembly And Use preview
14240
Бренд: Hudora Страницы: 8
Hudora 14112 Instructions On Assembly And Use preview
14112
Бренд: Hudora Страницы: 8
Hudora 14124 Instructions On Assembly And Use preview
14124
Бренд: Hudora Страницы: 28
Faraday Porteur Quick Start Manual preview
Porteur
Бренд: Faraday Страницы: 7
Yamaha 5GJ5 Supplementary Service Manual preview
5GJ5
Бренд: Yamaha Страницы: 40
Yamaha AEROX NS50 Owner'S Manual preview
AEROX NS50
Бренд: Yamaha Страницы: 74
Yamaha AEROX YQ50 Owner'S Manual preview
AEROX YQ50
Бренд: Yamaha Страницы: 84
Yamaha 2002 YB50 Service Manual preview
2002 YB50
Бренд: Yamaha Страницы: 161
Yamaha AEROX YQ50 Service Manual preview
AEROX YQ50
Бренд: Yamaha Страницы: 192
Yamaha 2002 CS50 Service Manual preview
2002 CS50
Бренд: Yamaha Страницы: 204
Yamaha 2009 XP500Y TMAX Service Manual preview
2009 XP500Y TMAX
Бренд: Yamaha Страницы: 386
Yamaha 2004 YP400 Service Manual preview
2004 YP400
Бренд: Yamaha Страницы: 417
Yamaha 2007 XP500 Service Manual preview
2007 XP500
Бренд: Yamaha Страницы: 450

Бренды по названию

Популярные бренды

Загрузить еще бренды