Yamaha YP125R Скачать руководство пользователя страница 150

Страница: 150 / 498

ENGINE (YP250R)

3-23

EAS20600

ADJUSTING THE EXHAUST GAS VOLUME

TIP

Be sure to set the CO density level to standard,
and then adjust the exhaust gas volume.

1. Remove:

• Upper panel

Refer to “GENERAL CHASSIS” on page 4-1.

2. Set the main switch to “OFF”.
3. Disconnect:

• Self-diagnosis signal coupler

4. Connect:

• FI diagnostic tool “1”

5. While pressing the “MODE” button “1”, set

the main switch to “ON”.

TIP

• “DIAG” appears on the LCD “2” of the FI diag-

nostic tool.

• “POWER” LED (Green) “3” comes on.

6. Press the “UP” button to select the CO adjust-

ment mode “CO” or the diagnostic mode “DI-
AG”.

7. After selecting “CO”, press the “MODE” but-

ton.

8. Check that “C1” appears on the LCD of the FI

diagnostic tool, and then press the “MODE”
button.

9. Start the engine.

NOTICE

ECA37P1015

Perform the adjustment after the battery has
been sufficiently charged.

10.Change the CO adjustment volume by press-

ing the “UP” and “DOWN” buttons.

TIP

The CO adjustment volume and engine idling
speed appears on the LCD of the FI diagnostic
tool.
• To decrease the CO adjustment volume, press

the “DOWN” button.

• To increase the CO adjustment volume, press

the “UP” button.

11.Release the “DOWN” and “UP” buttons to ex-

ecute the selection.

12.Set the main switch to “OFF” to cancel the

mode.

13.Disconnect:

• FI diagnostic tool

14.Connect:

• Self-diagnosis signal coupler

15.Install:

• Upper panel

Refer to “GENERAL CHASSIS” on page 4-1.

EAS20640

ADJUSTING THE THROTTLE CABLE FREE
PLAY

1. Check:

• Throttle cable free play “a”

Out of specification

→

Adjust.

FI diagnostic tool

90890-03182

FI Diagnostic Tool

DIAG

FI Diagnostic Tool

1 5 5 0 r p m

C1 : -10

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды