Yamaha YP125R Скачать руководство пользователя страница 473 | Manualshive

Страница: 473 / 498

background image

ELECTRICAL COMPONENTS

8-76

EAS27990

CHECKING THE BULBS AND BULB
SOCKETS

TIP

Do not check any of the lights that use LEDs.

Check each bulb and bulb socket for damage or
wear, proper connections, and also for continuity
between the terminals.
Damage/wear

→

Repair or replace the bulb,

bulb socket or both.
Improperly connected

→

Properly connect.

No continuity

→

Repair or replace the bulb, bulb

socket or both.

Types of bulbs

The bulbs used on this vehicle are shown in the
illustration.
• Bulbs “a” and “b” are used for the headlights

and usually use a bulb holder that must be de-
tached before removing the bulb. The majority
of these types of bulbs can be removed from
their respective socket by turning them coun-
terclockwise.

• Bulbs “c” are used for turn signal and tail/brake

lights and can be removed from the socket by
pushing and turning the bulb counterclockwise.

Checking the condition of the bulbs

The following procedure applies to all of the
bulbs.
1. Remove:

• Bulb

WARNING

EWA37P1018

Since headlight bulbs get extremely hot,
keep flammable products and your hands
away from them until they have cooled
down.

NOTICE

ECA37P1039

• Be sure to hold the socket firmly when re-

moving the bulb. Never pull the lead, other-
wise it may be pulled out of the terminal in
the coupler.

• Avoid touching the glass part of a headlight

bulb to keep it free from oil, otherwise the
transparency of the glass, the life of the
bulb, and the luminous flux will be adverse-
ly affected. If the headlight bulb gets soiled,
thoroughly clean it with a cloth moistened
with alcohol or lacquer thinner.

2. Check:

• Bulb (for continuity)

(with the pocket tester)
No continuity

→

Replace.

TIP

Before checking for continuity, set the pocket
tester to “0” and to the “

Ω

×

1” range.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the positive tester probe to terminal

“1” and the negative tester probe to terminal
“2”, and check the continuity.

b. Connect the positive tester probe to terminal

“1” and the negative tester probe to terminal
“3”, and check the continuity.

c. If either of the readings indicate no continuity,

replace the bulb.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

«
...
471
472
473
474
475
...
»

Содержание YP125R



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP125R

Бренд: Razor Страницы: 16

Бренд: Ypsilon Страницы: 65

Бренд: IconBiT Страницы: 12

Tribred Free Rein

Бренд: Trikke Страницы: 36

Бренд: Trikke Страницы: 36

Бренд: Malaguti Страницы: 278

Бренд: Elebike Страницы: 4

Бренд: HTI Страницы: 16

Shoprider S-889SL

Бренд: Roma Medical Страницы: 20

Touring Deluxe 150cc

Бренд: Tank Страницы: 37

Бренд: Shoprider Страницы: 18

VELOCIPTOR ES 100W

Бренд: Trevi Страницы: 16

Бренд: Vermeiren Страницы: 32

MATRIX PN2H 50CC

Бренд: E-TON Страницы: 2

Бренд: Scooter & More Страницы: 19

Бренд: SCOOT AND RIDE Страницы: 22

Бренд: Scooty Страницы: 20

Бренд: Scooty Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды