Yamaha YP125R Скачать руководство пользователя | Manualshive

Страница: 432 / 498

background image

FUEL INJECTION SYSTEM

8-35

Setting the diagnostic mode

1. Set the main switch to “OFF”.
2. Disconnect the self-diagnosis signal coupler, and then connect the FI diagnostic tool “1” as shown.

3. While pressing the “MODE” button, set the main switch to “ON”.

TIP

• “DIAG” appears on the LCD of the FI diagnostic tool. If “CO” appears on the LCD of the FI diagnostic

tool, press the “UP” button to select “DIAG”.

• The “POWER” LED (green) comes on.

4. Press the “MODE” button.

TIP

The diagnostic code number “D01” appears on the LCD of the FI diagnostic tool.

5. Select the diagnostic code number corresponding to the fault code number by pressing the “UP” and

“DOWN” buttons.

TIP

• The diagnostic code number appears on the LCD (01-70).
• To decrease the selected diagnostic code number, press the “DOWN” button. Press the “DOWN” but-

ton for 1 second or longer to automatically decrease the diagnostic code numbers.

• To increase the selected diagnostic code number, press the “UP” button. Press the “UP” button for 1

second or longer to automatically increase the diagnostic code numbers.

6. Check the operation of the sensor or actuator.

• Sensor operation

The data representing the operating conditions of the sensor appear on the LCD.

• Actuator operation

Press the “MODE” button.

7. Set the main switch to “OFF” to cancel the diagnostic mode.
8. Disconnect the FI diagnostic tool and connect the self-diagnosis signal coupler.

TIP

Information about each diagnostic code number is organized in this manual as follows:
• If a diagnostic code number has a corresponding fault code number, the information is shown in

“TROUBLESHOOTING DETAILS”. (Refer to “TROUBLESHOOTING DETAILS” on page 8-36.)

1

«
...
430
431
432
433
434
...
»

Содержание YP125R



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP125R

Бренд: DAELIM Страницы: 68

Бренд: GoYonder Страницы: 17

Бренд: Razor Страницы: 12

Бренд: Pride Mobility Страницы: 34

Бренд: techtron Страницы: 20

Бренд: Rebel Страницы: 32

Бренд: Hudora Страницы: 8

Бренд: Quantum Rehab Страницы: 2

Бренд: Trikke Страницы: 14

Бренд: KOMFI-RIDER Страницы: 28

Бренд: KOMFI-RIDER Страницы: 28

Бренд: KOMFI-RIDER Страницы: 28

Бренд: KOMFI-RIDER Страницы: 32

Бренд: Seago Страницы: 20

Бренд: Hover-1 Страницы: 28

YDX TORC PB65YTL

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 82

Бренд: Yamaha Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды