Yamaha YP125R Скачать руководство пользователя страница 281

Страница: 281 / 498

V-BELT AUTOMATIC TRANSMISSION (YP125R)

5-36

• Primary sliding sheave
• Spacer
• Primary sheave weights
• Cam

2. Lubricate:

• Oil seal
• Primary sliding sheave
• Spacer

TIP

Fill the notches of the primary sliding sheave
with grease. Apply grease to the inner surface of
the primary sliding sheave as shown.

NOTICE

ECA37P1003

Do not get any grease on the surfaces of the
sheaves. If any grease gets on the sheaves,
be sure to wipe it off with alcohol, etc.

EAS37P1036

ASSEMBLING THE SECONDARY SHEAVE

1. Lubricate:

• Secondary fixed sheave inner surface “1”
• Secondary sliding sheave inner surface “2”
• Oil seals
• Bearing

(with the recommended lubricant)

2. Install:

• Oil seal
• Secondary sliding sheave “1”

TIP

Install the secondary sliding sheave onto the
secondary fixed sheave “2” with the oil seal
guide “3”.

3. Install:

• Guide pins “1”

4. Lubricate:

• Guide pin grooves “2”

• O-rings “3”

(with the recommended lubricant)

5. Install:

• Spring seat
• Compression spring
• Clutch carrier “1”
• Clutch carrier nut “2”

TIP

• While compressing the compression spring

with the clutch spring holder “3” and clutch
spring holder arm “4”, install the clutch carrier
nut.

Recommended lubricant

BEL-RAY assembly lube®

Recommended lubricant

BEL-RAY assembly lube®

Oil seal guide (ø41)

90890-01396

Recommended lubricant

BEL-RAY assembly lube®

New

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды