Yamaha YP125R Скачать руководство пользователя

Страница: 487 / 498

ELECTRICAL COMPONENTS

8-90

b. Immerse the air temperature sensor “1” in a

container filled with water “2”.

TIP

Make sure that the air temperature sensor termi-
nals do not get wet.

c. Place a thermometer “3” in the water.

d. Heat the water or let it cool down to the spec-

ified temperatures.

e. Measure the air temperature sensor resis-

tance.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS37P1085

CHECKING THE ISC (IDLE SPEED
CONTROL) UNIT

TIP

Do not remove the ISC unit completely from the
throttle body.

1. Check:

• ISC unit

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Disconnect the ISC unit coupler from the ISC

unit.

b. Connect the pocket tester (

Ω

10) to the ter-

minals of the ISC unit.

c. Measure the ISC unit resistance.

Out of specification

→

Replace the throttle

body.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS37P1084

CHECKING THE V-BELT REPLACEMENT
INDICATOR RESET COUPLER

1. Remove:

• V-belt replacement indicator reset coupler

2. Check:

• V-belt replacement indicator reset coupler

Out of specification

→

Replace the V-belt re-

placement indicator coupler.

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

pink “1”

• Negative tester probe

→

light green “2”

• Positive tester probe

→

green “3”

• Negative tester probe

→

sky blue “4”

ISC unit resistance

27–33

Ω

at 20 °C (68 °F)

Continuity

Positive tester probe

→

black

“1”
Negative tester probe

→

black

“2”

Continuity

Positive tester probe

→

black

“2”
Negative tester probe

→

black

“1”

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды