Yamaha YP125R Скачать руководство пользователя страница 230

Страница: 230 / 498

FRONT FORK

4-55

7. Fill:

• Front fork leg

(with the specified amount of the recom-
mended fork oil)

NOTICE

ECA14230

• Be sure to use the recommended fork oil.

Other oils may have an adverse effect on
front fork performance.

• When disassembling and assembling the

front fork leg, do not allow any foreign ma-
terial to enter the front fork.

8. After filling the front fork leg, slowly stroke the

inner tube “1” up and down (at least ten
times) to distribute the fork oil.

TIP

Be sure to stroke the inner tube slowly because
the fork oil may spurt out.

9. Before measuring the fork oil level, wait ten

minutes until the oil has settled and the air
bubbles have dispersed.

TIP

Be sure to bleed the front fork leg of any residual
air.

10.Measure:

• Front fork leg oil level “a”

(from the top of the inner tube, with the inner
tube fully compressed and without the fork
spring)
Out of specification

→

Correct.

11.Install:

• Fork spring

EAS23050

INSTALLING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.
1. Install:

• Front fork leg “1”

WARNING

EWA37P1023

Make sure the brake hose is routed properly.

TIP

Pull up the inner tube until it stops, and then
tighten the lower bracket pinch bolts.

Recommended oil

Fork oil 10W or equivalent

Quantity

128.0 cm³ (4.33 US oz, 4.51
Imp.oz)

Level

109.0 mm (4.29 in)

Lower bracket pinch bolt

23 Nm (2.3 m·kgf, 17 ft·lbf)

2. Lower bracket

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды