Yamaha Electone F-25 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 122

background image

Operation

73

3. Push the power trim and tilt switch “

”

(down) to lower the outboard motor to
the desired position.

EMU28063

Shallow water

EMU28074

Cruising in shallow water (manual tilt
models)

WARNING

EWM01782



Run the boat at the lowest possible

speed when using the shallow water
cruising system. The tilt lock mecha-
nism does not work while the shallow
water cruising system is being used.
Hitting an underwater obstacle could
cause the outboard motor to lift out of
the water, resulting in loss of control.



Use extra care when operating in re-
verse. Too much reverse thrust can
cause the outboard motor to lift out of
the water, increasing the chance of ac-
cident and personal injury.

NOTICE

ECM00261

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

EMU28126

Procedure

1. Place the remote control lever / gear

shift lever in neutral.

DN

ZMU01936

DN

ZMU06546

6BP-9-3B-1E0.book 73 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
77
78
79
80
81
...
»

Содержание Electone F-25



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Electone F-25

Бренд: Gardner Bender Страницы: 4

Бренд: GAPS Страницы: 36

Бренд: yellow jacket Страницы: 26

Бренд: Olympus Страницы: 362

Бренд: Olympus Страницы: 8

Бренд: QuantAsylum Страницы: 70

Бренд: X-Rite Страницы: 45

Бренд: X-Rite Страницы: 22

Бренд: Yamaha Страницы: 6

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Electone Stagea ELS-01C

Бренд: Yamaha Страницы: 248

Бренд: Danfoss Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды