Yamaha Electone F-25 Скачать руководство пользователя страница 100

Страница: 100 / 122

Maintenance

bend the ends over securely. Otherwise,
the propeller could come off during oper-
ation and be lost.

1. Apply Yamalube Marine Grease or a

corrosion resistant grease to the propel-
ler shaft.

2. Install the spacer (if equipped), thrust

washer, washer (if equipped), and pro-
peller on the propeller shaft.

NOTICE:

Make sure to install the thrust washer
before installing the propeller. Other-
wise, the lower case and propeller
boss could be damaged.

[ECM01882]

3. Install the spacer (if equipped) and the

washer. Tighten the propeller nut to the
specified torque.

4. Align the propeller nut slot with the pro-

peller shaft hole. Insert a new cotter pin
in the hole and bend the cotter pin ends.

NOTICE:

Do not reuse the cotter pin.

Otherwise, the propeller can come off
during operation.

[ECM01892]

TIP:

If the propeller nut slot does not align with the
propeller shaft hole after tightening the pro-
peller nut to the specified torque, tighten the
nut further to align the slot with the hole.

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

ZMU06564

1. Cotter pin
2. Propeller nut
3. Washer
4. Propeller
5. Thrust washer

Propeller nut tightening torque:

34 Nm (3.47 kgf-m, 25.1 ft-lb)

ZMU06603

ZMU02063

6BP-9-3B-1E0.book 94 ページ２０１５年１１月１６日　月曜日　午後５時５７分

Содержание Electone F-25



























































































































Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды

Yamaha Electone F-25, Руководство пользователя

Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды