Yamaha Electone F-25 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 122

background image

Maintenance

80

2. Lubricate all grease fittings. For further

details, see page 86.

TIP:

For long-term storage, fogging the engine
with fogging oil is recommended. Contact
your Yamaha dealer for information about
fogging oil and procedures for your outboard
motor.

EMU30268

Cleaning and anticorrosion
measures

1. Wash down the exterior of the outboard

motor with fresh water and dry off com-
pletely.

NOTICE:

Do not spray water

into the air intake.

[ECM01841]

For further

information, see page 81.

2. Spray the outboard motor exterior with

“Yamaha Silicone Protectant”.

NOTICE:

Do not spray when the engine is run-
ning. Also, do not spray near the si-
lencer or into the engine. Otherwise
the engine could be damaged.

[ECM01403]

3. Wax the cowling with a non-abrasive

wax such as “Yamaha Silicone Wax”.

EMU28446

Flushing power unit

Perform this procedure right after operation
for the most thorough flushing.

NOTICE

ECM01531

Do not perform this procedure while the
engine is running. The water pump may
be damaged and severe damage from
overheating can result.

1. After shutting off the engine, unscrew

the garden hose connector from the fit-
ting on the bottom cowling.

2. Screw the garden hose adapter onto a

garden hose, which is connected to a
fresh water supply, and then connect it
to the garden hose connector.

3. With the engine off, turn on the water tap

and let the water flush through the cool-
ing passages for about 15 minutes. Turn
off the water and disconnect the garden
hose adapter from the garden hose con-
nector.

4. Reinstall the garden hose connector

onto the fitting on the bottom cowling.
Tighten the connector securely.

NOTICE:

Do not leave the garden

hose connector loose on the bottom
cowling fitting or let the hose hang
free during normal operation. Water

1. Fitting
2. Garden hose connector
3. Garden hose adapter

1

3

2

ZMU06553

6BP-9-3B-1E0.book 80 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
84
85
86
87
88
...
»

Содержание Electone F-25



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Electone F-25

Бренд: RayTek Страницы: 72

Бренд: Magnetrol Страницы: 40

Бренд: B meters Страницы: 2

Бренд: Omega Страницы: 31

Бренд: Hilti Страницы: 146

Бренд: Hilti Страницы: 31

Бренд: PICO Страницы: 2

Trimble Ranger 3

Бренд: Badger Meter Страницы: 20

Бренд: A&D Страницы: 38

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренд: yellow jacket Страницы: 16

Prosonic S FMU90 PROFIBUS DP

Бренд: Endress+Hauser Страницы: 110

Бренд: X-Rite Страницы: 21

Бренд: DeNovix Страницы: 93

Бренд: GE Страницы: 16

Digalox DPM72-MPPA

Бренд: TDE Instruments Страницы: 8

PROline promag 23

Бренд: Endress+Hauser Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды