Yamaha Electone F-25 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 122

background image

Operation

70

EMU33153

Procedure for tilting up (hydro tilt
models)

1. Place the gear shift lever in neutral.

2. Place the tilt lock lever in the release po-

sition.

3. Hold the rear of the top cowling with one

hand, tilt the engine up, and turn the tilt
support lever toward you or tilt support
knob into the clamp bracket, and then
place the tilt lock lever back into the lock

position to support the outboard motor.

NOTICE:

Do not use the tilt support

lever or knob when trailering the
boat. The outboard motor could
shake loose from the tilt support and
fall. If the motor cannot be trailered in
the normal running position, use an
additional support device to secure it
in the tilt position. For more detailed
information, see page 77.

[ECM01642]

EMU44590

Procedure for tilting up (power trim
and tilt models)

1. Place the remote control lever / gear

shift lever in neutral.

ZMU06503

N

ZMU06521

ZMU07537

ZMU06543

N

ZMU03196

6BP-9-3B-1E0.book 70 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
74
75
76
77
78
...
»

Содержание Electone F-25



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Electone F-25

Бренд: UEi Страницы: 20

Бренд: Hach Страницы: 138

Бренд: Unico Страницы: 10

Бренд: OHAUS Страницы: 2

Veeder-Root 7990 Series

Бренд: Danaher Страницы: 8

Бренд: EUPRY Страницы: 6

Бренд: REED Страницы: 4

Бренд: JUMO Страницы: 24

SignalHawk SH-36S-PC

Бренд: BIRD Страницы: 137

Бренд: Alpes Lasers Страницы: 41

Бренд: Thermo Scientific Страницы: 56

Бренд: Velleman Страницы: 15

Бренд: Chauvin Arnoux Страницы: 64

1101-3121-0049-800

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Isspro Страницы: 2

Бренд: Hanna Instruments Страницы: 16

Бренд: Dewetron Страницы: 48

Бренд: East Tester Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды