Yamaha Electone F-25 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 122

background image

Trouble Recovery

107

5. Insert the knotted end of the emergency

starter rope into the notch in the flywheel
magnet and wind the rope 1 or 2 turn(s)
around the flywheel magnet clockwise.

6. Pull the rope slowly until resistance is

felt. Give a strong pull straight out to
crank and start the engine. If the engine
does not start on the first try, repeat the
procedure.

TIP:



If the engine does not start on the first try,
repeat the procedure. If the engine fails to
start after 4 or 5 tries, open the throttle a
small amount (between 1/8 and 1/4) and
try again. Also if the engine is warm and
fails to start, open the throttle a same
amount and try to start the engine again. If
the engine still fails to start, see page 54.



Slowly return the throttle grip to the fully
closed position so that the engine does not
stall.

EMU33502

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately.

NOTICE:

Do not attempt to run the

outboard motor until it has been com-
pletely inspected.

[ECM00402]

ZMU01772

ZMU02026

ZMU06584

6BP-9-3B-1E0.book 107 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
111
112
113
114
115
...
»

Содержание Electone F-25



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Electone F-25

Masoneilan 12400 Series

Бренд: Baker Hughes Страницы: 81

Бренд: Valeport Страницы: 27

Бренд: Artesia Страницы: 36

Бренд: Hach Страницы: 96

Бренд: TASKING Страницы: 12

Бренд: Hanna Instruments Страницы: 9

Бренд: Cecomp Страницы: 4

Dakota Ultrasonics ZX-2

Бренд: ABQ Industrial Страницы: 27

SoundAdvisor NMS045

Бренд: Larson Davis Страницы: 64

Бренд: Tenma Страницы: 52

Бренд: IDT Страницы: 20

Бренд: Eagletone Страницы: 3

Бренд: Fluke Страницы: 2

Бренд: SAND Страницы: 15

Бренд: SNV Engineering Страницы: 43

Telecaster Bass

Бренд: Fender Страницы: 16

Бренд: NARDA Страницы: 60

Бренд: E+E Elektronik Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды