Yamaha Electone F-25 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 122

background image

Trouble Recovery

103

EMU29513

Power trim and tilt will not operate

If the engine cannot be tilted up or down with
the power trim and tilt because of a dis-
charged battery or a failure with the power
trim and tilt unit , the engine can be tilted
manually.
1. Loosen the manual valve screw by turn-

ing it clockwise until it stops.

2. Put the engine in the desired position,

then tighten the manual valve screw by
turning it counterclockwise.

EMU29534

Starter will not operate

If the starter mechanism does not operate
(the engine cannot be cranked with the start-
er), the engine can be started with an emer-
gency starter rope.

WARNING

EWM01023



Use this procedure only in an emergen-
cy to return to the nearest port for re-
pairs.



When the emergency starter rope is
used to start the engine, the start-in-
gear protection device does not oper-
ate. Make sure the remote control lever
is in neutral. Otherwise the boat could
unexpectedly start to move, which
could result in an accident.



Attach the engine shut-off cord to a se-
cure place on your clothing, or your
arm or leg while operating the boat.



Do not attach the cord to clothing that
could tear loose. Do not route the cord
where it could become entangled, pre-
venting it from functioning.



Avoid accidentally pulling the cord dur-

1. Fuse puller
2. Cap
3. Fuse (20 A, 30 A)
4. Spare fuse (20 A, 30 A)

1. Fuse puller

1

2

3

4

ZMU06565

1

ZMU04337

1. Manual valve screw

ZMU02816

1

6BP-9-3B-1E0.book 103 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
107
108
109
110
111
...
»

Содержание Electone F-25



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Electone F-25

Бренд: Yamaha Страницы: 3

Clavinova CVP-601

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 28

Бренд: RHS Страницы: 8

SF6 Portable Monitor

Бренд: Bacharach Страницы: 2

Бренд: NIEUWKOOP Страницы: 2

Бренд: Oceanic Страницы: 114

Tube Location GA-9

Бренд: Gibson Страницы: 1

Бренд: wattwatchers Страницы: 14

Бренд: X-Rite Страницы: 54

Бренд: BART Страницы: 24

Бренд: SAND Страницы: 15

Бренд: SNV Engineering Страницы: 43

Бренд: Kawai Страницы: 16

Бренд: dacell Страницы: 21

Бренд: Apera Instruments Страницы: 30

Бренд: Endress+Hauser Страницы: 54

Бренд: PCB Piezotronics Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды