Yamaha Electone F-25 Скачать руководство пользователя страница 78

Страница: 78 / 122

Operation

EMU30193

Procedure for tilting down (manual
tilt models)

1. Place the tilt lock lever in the lock posi-

tion.

2. Slightly tilt the engine up until the tilt sup-

port bar is automatically released.

3. Slowly tilt the engine down.

EMU34481

Procedure for tilting down (hydro tilt
models)

1. Release the tilt lock lever.

2. Hold the rear of the top cowling with one

hand, tilt the outboard motor up slightly
and pull out the tilt support knob or re-
turn the tilt support lever.

3. Slowly tilt the outboard motor down.
4. Place the tilt lock lever in the lock posi-

tion.

EMU44601

Procedure for tilting down (power
trim and tilt models)

1. Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support knob
becomes free.

2. Pull out the tilt support knob.

ZMU02306

ZMU07539

ZMU06545

ZMU07536

ZMU06545

6BP-9-3B-1E0.book 72 ページ２０１５年１１月１６日　月曜日　午後５時５７分

Содержание Electone F-25



























































































































Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды

Yamaha Electone F-25, Руководство пользователя

Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды