Yamaha Electone F-25 Скачать руководство пользователя страница 55

Страница: 55 / 122

Operation

EMU40994

Engine oil

1. Place the outboard motor in a vertical

position (not tilted).

NOTICE:

If the out-

board motor is not level, the oil level
indicated on the oil dipstick may not
be accurate.

[ECM01862]

2. Remove the oil dipstick and wipe it

clean.

3. Insert the oil dipstick completely and re-

move it again.

4. Check that the oil level on the oil dipstick

is between the upper and lower marks.
Consult your Yamaha dealer if the oil
level is not at the proper level or if it ap-
pears milky or dirty.

EMU27154

Engine



Check the engine and engine mounting.



Look for loose or damaged fasteners.



Check the propeller for damage.



Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out
and the engine can overheat during oper-
ation.

[ECM01802]

EMU36956

Install top cowling

1. Be sure that the cowling lock lever is re-

leased.

2. Be sure that the rubber seal is seated all

the way around the top cowling.

3. Place the top cowling on the bottom

cowling.

4. Check to be sure the rubber seal is seat-

ed correctly between the top cowling
and the bottom cowling.

5. Move the cowling lock lever to lock the

top cowling as shown.

NOTICE:

If the

1. Oil dipstick

1. Oil dipstick
2. Lower mark
3. Upper mark

ZMU06515

ZMU06516

1. Fitting
2. Flushing device

ZMU06517

6BP-9-3B-1E0.book 49 ページ２０１５年１１月１６日　月曜日　午後５時５７分

Содержание Electone F-25



























































































































Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды

Yamaha Electone F-25, Руководство пользователя

Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды