Yamaha Electone F-25 Скачать руководство пользователя страница 104

Страница: 104 / 122

Maintenance

3. The electrical contacts of the battery and

cables must be clean and properly con-
nected, or the battery will not start the
engine.

EMU29372

Disconnecting the battery

1. Turn off the battery cut-off switch (if

equipped) and main switch.

NOTICE:

they are left on, the electrical system
can be damaged.

[ECM01931]

2. Disconnect the negative cable(s) from

the negative (-) terminal.

NOTICE:

Al-

ways disconnect all negative (-) ca-
bles first to avoid a short circuit and
damage to the electrical system.

[ECM01941]

3. Disconnect the positive cable(s) and re-

move the battery from the boat.

4. Clean, maintain, and store the battery

according to the manufacturer’s instruc-
tions.

1. Red cable
2. Black cable
3. Battery

ZMU01811

6BP-9-3B-1E0.book 98 ページ２０１５年１１月１６日　月曜日　午後５時５７分

Содержание Electone F-25



























































































































Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды

Yamaha Electone F-25, Руководство пользователя

Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды