Yamaha Electone F-25 Скачать руководство пользователя страница 102

Страница: 102 / 122

Maintenance

level plug hole, insert and tighten the oil
level plug.

7. Put a new gasket on the gear oil drain

screw. Insert and tighten the gear oil
drain screw.

EMU29318

Inspecting and replacing anode(s)

Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect the
external anodes periodically. Remove scales
from the surfaces of the anodes. Consult a
Yamaha dealer for replacement of external
anodes.

NOTICE

ECM00721

Do not paint anodes, as this would render
them ineffective.

Tightening torque:

7 Nm (0.71 kgf-m, 5.2 ft-lb)

Tightening torque:

7 Nm (0.71 kgf-m, 5.2 ft-lb)

ZMU06559

ZMU03664

ZMU02924

ZMU05024

ZMU07535

6BP-9-3B-1E0.book 96 ページ２０１５年１１月１６日　月曜日　午後５時５７分

Содержание Electone F-25



























































































































Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды

Yamaha Electone F-25, Руководство пользователя

Результаты поиска

Содержание Electone F-25

Отзывы:

Похожие инструкции для Electone F-25

Бренды по названию

Популярные бренды