Yamaha Electone F-25 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 122

background image

Operation

71

2. Press the power trim and tilt switch “

”

(up) until the outboard motor has tilted
up completely.

3. Push the tilt support knob into the clamp

bracket to support the engine.

WARNING! After tilting the outboard
motor, be sure to support it with the
tilt support knob or tilt support lever.
Otherwise the outboard motor could
fall back down suddenly if oil in the
power trim and tilt unit or in the pow-
er tilt unit loses pressure.

[EWM00263]

NOTICE:

Do not use the tilt support

lever or knob when trailering the
boat. The outboard motor could
shake loose from the tilt support and
fall. If the motor cannot be trailered in
the normal running position, use an
additional support device to secure it
in the tilt position. For more detailed
information, see page 77.

[ECM01642]

UP

ZMU01787

UP

ZMU06537

ZMU06543

6BP-9-3B-1E0.book 71 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
75
76
77
78
79
...
»

Содержание Electone F-25



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Electone F-25

Бренд: Keithley Страницы: 48

Бренд: Van Walt Страницы: 6

Бренд: zebris Страницы: 42

Бренд: Labom Страницы: 5

Бренд: Shimpo Страницы: 68

Бренд: SEFRAM Страницы: 31

Бренд: Milkotester Страницы: 44

Бренд: DeFelsko Страницы: 25

Бренд: Velleman Страницы: 13

Бренд: A&D Страницы: 2

Бренд: Bulteh 2000 Страницы: 80

dry-cal dc-lite

Бренд: BIOS Страницы: 10

Бренд: SMPE Страницы: 2

Бренд: Dewetron Страницы: 48

Бренд: GE Страницы: 16

Бренд: Hanna Instruments Страницы: 2

Бренд: Seli Страницы: 68

Бренд: E+E Elektronik Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды