Yamaha Electone F-25 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 122

background image

43

Installation

EMU26903

Installation

The information presented in this section is
intended as reference only. It is not possible
to provide complete instructions for every
possible boat and motor combination. Proper
mounting depends in part on experience and
the specific boat and motor combination.

WARNING

EWM01591



Overpowering a boat could cause se-
vere instability. Do not install an out-
board motor with more horsepower
than the maximum rating on the capac-
ity plate of the boat. If the boat does not
have a capacity plate, consult the boat
manufacturer.



Improper mounting of the outboard mo-
tor could result in hazardous condi-
tions such as poor handling, loss of
control, or fire hazards. For permanent-
ly mounted models, your dealer or oth-
er person experienced in proper rigging
should mount the motor.

EMU33471

Mounting the outboard motor

The outboard motor should be mounted so
that the boat is well balanced. Otherwise, the
boat could be hard to steer. For single-en-
gine boats, mount the outboard motor on the
centerline (keel line) of the boat.

EMU26926

Mounting height

To run your boat at optimum efficiency, the
water resistance (drag) of the boat and out-
board motor must be made as little as possi-
ble. The mounting height of the outboard
motor greatly affects the water resistance. If
the mounting height is too high, cavitation
tends to occur, thus reducing the propulsion;
and if the propeller tips cut the air, the engine
speed will rise abnormally and cause the en-
gine to overheat. If the mounting height is too
low, the water resistance will increase and
thereby reduce engine efficiency. Mount the
outboard motor so that the anti-cavitation
plate is between the bottom of the boat and
a level 25 mm (1 in) below it.

1. Center line (keel line)

ZMU01760

1

6BP-9-3B-1E0.book 43 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
47
48
49
50
51
...
»

Содержание Electone F-25



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Electone F-25

Бренд: Ultrasound Страницы: 6

Бренд: Lambrecht Страницы: 5

Бренд: Keithley Страницы: 25

Бренд: Hammond Organ Страницы: 25

Бренд: Hammond Organ Страницы: 87

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Бренд: LaserLiner Страницы: 52

Бренд: Veris Страницы: 8

VIBRO-KING P/N 053493

Бренд: Fender Страницы: 8

Бренд: Macnaught Страницы: 8

Бренд: Motortech Страницы: 142

Smart Air Quality Monitor

Бренд: Lennox Страницы: 28

Бренд: Roland Страницы: 96

Orion Versa Star Pro Series

Бренд: Thermo Scientific Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: FuzzDog Страницы: 6

Бренд: PCE Health and Fitness Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды