WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 88

Страница: 88 / 194

WhitakerAudio

•

One 1/4-inch jack

•

Pilot lamp (PL51)

•

Power switch (SW51)

•

Speaker on/off switch (SW52)

•

Auto-Off enable/disable switch (SW202)

•

Front panel knobs (quantity = 2)

– Install the front panel handles using the #8 hardware provided. Be careful to not scratch

the finish. Note that the front panel handles are decorative and should not be used to move

the amplifier after it has been completed.

– Find SW52, the Speaker On/Off switch. There are two nuts provided; only one will be

used. Place the lockwasher provided on the shaft. Note that one side of the mounting shaft

has a key; this key should face upward. Insert the switch into the chassis and then fit the

front panel onto the shaft. Use one of the nuts to secure the switch/chassis/panel assembly.

Do not tighten.

– Find SW202, the Auto-Off enable/disable switch. There are two nuts provided; only one

will be used. Place the lockwasher provided on the shaft. Note that one side of the

mounting shaft has a key; this key should face downward. Insert the switch into the

chassis and then fit the front panel onto the shaft. Use one of the nuts to secure the switch/

chassis/panel assembly. Do not tighten.

– Install R35, the right channel Volume control –

100 k

, potentiometer, panel mount

Using a pair of long-nose pliers, bend the three terminals slightly toward the back of the

potentiometer. Note that there is a key tab at the base of the potentiometer. Using the

pliers, bend this tab down toward the face of the component so it is out of the way. Mount

R35 as follows. Place a lockwasher on the shaft and feed the component through the

chassis/front panel. Install a lockwasher and then a flat washer on the shaft. Secure with

the nut provided. Do not tighten. The terminals of the potentiometers should face

downward toward the chassis bottom plate.

– Install R36, the left channel Volume control –

100 k

, potentiometer, panel mount

Using a pair of long-nose pliers, bend the three terminals slightly toward the back of the

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды