WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 132

Страница: 132 / 194

132

WhitakerAudio

– Cut two short pieces of small heat-shrink tubing, each about 3/4-inch long. Place the

tubing at each end of the audio cable. Process.

– Insert the Molex socket into the

Conn4

connector on the left channel PWB. Note that the

drain wire goes to the first “GND” position.

– Attach the shield wire of the audio cable to terminal #1 (low) on the

left channel Volume

control

. Do not solder.

– Attach the white wire of the audio cable to terminal #2 (arm) on the left channel Volume

control. Solder.

– Prepare a 28-inch long audio cable. Cut two short pieces of small heat-shrink tubing, each

about 3/4-inch long. Place the tubing at each end of the audio cable. Process.

– Connect the audio cable just prepared to the

Left Channel Input

jack on the back panel.

The white wire goes to the center pin and the shield goes to the shell. Solder.

– Route the audio cable to the front panel using the cable clamps along side the preamplifier

power supply PWB.

– Connect the white wire of the 28-inch long audio cable to the high terminal (#3) of the left

channel Volume control. Solder. Connect the shield to the low terminal (#1) of the left

channel Volume control. Solder (2 wires).

– Prepare a 28-inch long audio cable. Cut two short pieces of small heat-shrink tubing, each

about 3/4-inch long. Place the tubing at each end of the audio cable. Process.

– Connect the audio cable just prepared to the

Right Channel Input

jack on the back panel.

The white wire goes to the center pin and the shield goes to the shell. Solder.

– Route the audio cable to the front panel using the cable clamps along side the right

channel PWB and the chassis side.

– Connect the white wire of the 28-inch long audio cable to the high terminal (#3) of the

right channel Volume control. Solder. Connect the shield to the low terminal (#1) of the

right channel Volume control. Solder (2 wires).

– Using the tie wraps provided, organize the audio cabling and other wiring in the amplifier.

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды