WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 152

Страница: 152 / 194

152

WhitakerAudio

Note that when the optional companion preamplifier is connected to the Auxiliary Power

Connector, the B+ voltage will be approxi250 V dc. The total current draw of the

amplifier with the preamplifier connected will be just over 1 A.

6.2.2

Feedback Trim Adjustment

Resistors R47 and R48 provide for fine adjustments of the negative feedback level to the input

stage of the amplifier (V1 and V4). The Feedback Trim potentiometers are 15-turn devices. At

one extreme, the overall feedback is approximately 24 dB; at the other extreme it is 27 dB.

Greater negative feedback results in lower (improved) distortion levels, but also reduced input

sensitivity.

The Feedback Trim potentiometers are used to maximize the negative feedback of the

amplifier for the desired input sensitivity, which is 1.0 V rms for full rated output (10 W). The

setup procedure is as follows:

•

Connect a 10 W or greater non-inductive load to each channel of the amplifier. Apply

power.

•

Connect an audio voltmeter to the right channel output terminals. Connect a 1 kHz audio

source to the right channel input RCA jack. Set the Volume control fully clockwise.

•

Adjust the 1 kHz audio source for a voltage of 1.0 V rms at the RCA jack. Adjust R47 to

produce an output voltage of 8.9 V rms at the speaker terminals. Turn the trimmer

clockwise to increase feedback (and decrease sensitivity).

•

Disconnect the test equipment from the right channel and connect it to the left channel.

•

Adjust the 1 kHz audio source for a voltage of 1.0 V rms at the RCA jack. Adjust R48 to

produce an output voltage of 8.9 V rms at the speaker terminals. Turn the trimmer

counter-clockwise to increase feedback (and decrease sensitivity).

•

Switch the amplifier off and remove the test equipment connections.

In addition to maximizing the amount of negative feedback, the Feedback Trim

potentiometers also compensate for minor gain variations between channels. Such sensitivity

differences are usually small, caused primarily by different performance characteristics of the

pentode input tubes.

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды