WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 105

Страница: 105 / 194

105

20 W Stereo Audio Amplifier

– Connect 50V – plate winding bias tap. Find the

violet

lead from the power transformer.

Install a connector to the wire. Attach to the

50V

post on the rectifier PWB.

– Connect T51CT – plate winding center tap. Find the

red/yellow

lead from the power

transformer. Install a connector to the wire. Attach to the

T51ct

post on the rectifier PWB.

– Connect 6VH1 – 6.3 V filament. Find one of the

green

leads from the power transformer.

Install a connector to the wire. Attach to the one of

6VH1

post on the rectifier PWB.

– Connect 6VH2 – 6.3 V filament. Find the remaining

green

lead from the power

transformer. Install a connector to the wire. Attach to one of the

6VH2

post on the rectifier

PWB.

– Connect 6VHct – 6.3 V filament center-tap. Find the

green/yellow

lead from the power

transformer. Install a connector to the wire. Attach to the

6VHct

post on the rectifier

PWB.

It is unlikely that the 5 V heater leads (yellow, yellow, black/yellow center-tap) will reach

their respective terminal posts on the left channel PWB. These leads will therefore need to be

extended. Use the following procedure.

– Cut two 11-inch long pieces of #22 yellow wire. Attach a quick-disconnect terminal to one

end of each wire. Attach a male quick-disconnect terminal to the free end of each wire.

– Connect 5VHa – 5 V heater. Connect one of the yellow wires to the

5VHa

post on the left

channel PWB.

– Connect 5VHb – 5 V heater. Connect the remaining yellow wire to the

5VHb

post on the

left channel PWB.

– Twist the yellow wires together along their length and route to the rectifier PWB.

– Find one of the

yellow

lead from the power transformer. Install a quick-disconnect

terminal to the wire. Mate with one of the yellow wires from the left channel PWB.

– Find the remaining

yellow

lead from the power transformer. Install a quick-disconnect

terminal to the wire. Mate with the remaining yellow wire from the left channel PWB.

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя, Страница: 105 / 194

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы: