WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 36

Страница: 36 / 194

WhitakerAudio

The amplifier PWBs are connected to the chassis through the mounting holes for the vacuum

tubes. Additional supporting posts are provided at each corner of the board.

The tube sockets are conventional chassis-mounted devices, with jumper leads extending

from the active pins to the PWB. The sockets are held away from the PWB using standoffs. This

approach permits the sockets to be firmly mounted on the chassis, rather than being physically

supported by the PWB. This approach also keeps heat above the chassis and away from the PWB,

which can degrade over time due to excessive heat.

Hot-7

AC hot buss

Black

Connects to preamp power supply

Hot-8

AC hot buss

White

Connects to pilot light PL51

Not connected

Blue/yellow

Connects to blue/yellow primary lead from T51

Not connected

Brown/yellow

Connects to brown/yellow primary lead from
T51

Not connected

Black/red

Connects to black/red primary lead from T51

Not connected

White/black

Connects to the white/black primary lead from
T51

Not connected

GND

Ground

Black

Connects to main chassis ground point

6VH1

6 V ac heater

Green

Connects to the

6VH1

post on Rectifier PWB

6VH2

6 V ac heater

Brown

Connects to the

6VH2

post on Rectifier PWB

PL1

Plate from V2

Blue

Connects to blue lead from T1

SC1

Screen from V2

Blue/yellow

Connects to blue/yellow lead from T1

PL2

Plate from V3

Brown

Connects to brown lead from T1

SC2

Screen from V3

Brown/yellow

Connects to brown/yellow lead from T1

T1ct

B+ to output transformer

Red

Connects to red lead from T1

Table 3.1

Amplifier PWB #1 (right) Connection Wiring Codes

(Note that the color codes for the transformers listed in this table may vary. Consult device

documentation before proceeding.)

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды