WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 113

Страница: 113 / 194

113

20 W Stereo Audio Amplifier

– Attach one end of the wire prepared in the previous step to the

Hot-3

post on the right

channel PWB. Attach the other end of the wire to the

RYL51

COM

post. Note that the

terminal legend for the relay is given on the top side of the device. Insert the connector

straight down on the relay terminal. Do not bend the terminal as that may crack the

housing

– Prepare two 28-inch long #22 white wires, twisted. Install quick-disconnect terminals on

each wire at one end of the twisted pair. On the other end of the twisted pair, install the

miniature quick-disconnect connectors provided with the relay. Note that these two

connector types are not interchangeable.

– Attach the white twisted pair miniature connectors to the mating “coil” posts on RYL51.

Attach one of the standard-size connectors to the

RYL51+

post on the left channel PWB.

Attach the other connector to the

RYL51-

post. Use the available cable clamps for

routing.

– Prepare one 21-inch long #22 white wire. Attach a quick-disconnect terminal to one end of

the wire. Attach to the

N-4

(AC neutral to PL51) post on the right channel PWB. Route the

other end of the wire toward the front panel. It will be connected later.

– Prepare one 20-inch long #22 white wire. Attach a quick-disconnect terminal to one end of

the wire. Attach to the

Hot-8

(AC hot to PL51) post on the right channel PWB. Route the

other end of the wire toward the front panel.

– The two #22 white wires will connect to the front panel pilot lamp. Position the wire ends

at the lamp and observe where their paths intersect. Twist the wires together along this

path. Route the wires to the front panel.

– Connect one white wire to each of the two terminals on the pilot lamp. Solder. A short

piece of small heat-shrink tubing may be used on each wire, if desired.

Note: It may be helpful to temporarily remove the front panel power switch in order to make

the connections to the pilot lamp.

– Find

VR54

, 130 V MOV. Place a 1-inch long piece of insulation on each lead (use

insulation stripped from a length of #18 black hookup wire). Attach a quick-disconnect

terminal to each lead. Connect one lead to

N-6

on Amplifier PWB #1 (right channel).

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды