WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 94

Страница: 94 / 194

WhitakerAudio

– Mount the external power supply connector using the #4 hardware provided. The socket

mounting pad rests against the outside of the back panel. Note the pin numbers printed on

the connector side of the socket. Orient the socket so the lettering is upright when viewed

from the rear panel. Set the companion plug and terminals aside. They will be installed

later.

– Collect the free end of the wiring harness. Insert the Molex terminals into the 8-pin Molex

housing as follows:

•

#22 black wire to pin #1

•

#22 white wire to pin #2

•

#22 white wire to pin #3

•

#22 red wire to pin #4

•

#18 green wire to pin #5

•

#18 green wire to pin #6

•

#22 blue wire to pin #7

•

#22 blue wire to pin #8

Leave the Molex connector free. It will be connected later to the preamplifier power supply

PWB.

The auxiliary power connector has now been installed. Double-check your work.

The back panel components have now been installed. Figure 5.10 shows the back panel and

top of the chassis at this stage in construction.

5.6.3

Cable Clamps and Related Hardware

Some of the cable clamp mounting screws will not be accessible after the PWBs have been

installed. Therefore, they need to be installed first. Three of the screws that hold the cable clamps

also serve as mounting posts for the acrylic cover.

See the chassis layout drawing in Figure 5.11. Note the locations of the cable clamps. Note

also that three cable clamp positions are also identified as acrylic cover mounting posts.

– Find the cable clamp hardware package. There are ten sets in this package. Install the

cable clamps using the #6 hardware provided for the six single-purpose cable clamps

(those not designated as also a acrylic cover mounting post). Note that the flat washer

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды