WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 133

Страница: 133 / 194

133

20 W Stereo Audio Amplifier

The audio input and control circuit connections have now been made. Double check your

work before moving on.

5.6.16 Preamplifier Power Supply

Locate the preamplifier power supply PWB. Because of the tight spacing of some of the

connection points, most of the wiring to the board will be completed before the board is inserted

in the chassis.

– Remove the mounting screws in the standoffs at the four corners of the PWB and the three

inner positions (if present). Set these in a convenient place.

– Find the #22 violet wire from the power management PWB. Connect to the

35Vdc

post on

the preamplifier power supply PWB.

– Insert the 8-terminal Molex connector into Conn301.

– Carefully place the preamplifier power supply board in position from the underside of the

chassis. Observe the match between the holes on the side of the chassis and the PWB

standoffs. All should align. If one or more standoffs do not properly align with the

mounting holes on the chassis, loosen and then re-tighten the standoff(s) and try again.

Note that some of the connection terminals on the preamplifier power supply PWB slide in-

between connection terminals on the left channel PWB. It may take a little work to properly place

the board into position. After the PWB has been mounted, check to make sure no wires are

pinched where the connectors of the two boards mesh. Install the seven 4-40 x 1/4-inch mounting

screws from the side of the chassis to the standoffs on the preamplifier power supply circuit

board. Do not tighten the screws until all screws have been threaded. The mounting screws should

be snug; do not over-tighten.

– Find the #18 black wire from the main ground point. Connect to the ground lug on the

preamplifier power supply PWB. Do not solder.

– Find the #18 black wire from the rear panel preamplifier connector, pin #9. Connect to the

ground lug on the preamplifier power supply PWB. Solder (2 wires).

– Find the white #18 wire from the right channel PWB. Attach a quick-disconnect terminal

and connect to the

N-5

post on the preamplifier power supply PWB.

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды