WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 106

Страница: 106 / 194

106

WhitakerAudio

•

Find the

black/yellow

lead from the power transformer. Install a quick-disconnect

terminal to the wire. This wire is not connected. Secure with a tie-rap so it does not make

contact with any open circuits.

The following steps assume a line input voltage of 120 V ac.

– Connect N-2 – AC neutral to T51. Find the

brown

lead from the power transformer.

Install a connector to the wire. Attach to the

N-2

post on the right channel PWB. Route the

wire below the cable to output transformer T1.

– Connect N-3 – AC neutral to T51. Find the

white

lead from the power transformer. Install

a connector to the wire. Attach to the

N-3

post on the right channel PWB. Route the wire

below the cable to output transformer T1.

– Connect Hot-4 – AC hot to T51. Find the

blue

lead from the power transformer, T51.

Install a connector to the wire. Attach to the

Hot-4

post on the right channel PWB.

– Connect Hot-5 – AC hot to T51. Find the

black

lead from the power transformer, T51.

Install a connector to the wire. Attach to the

Hot-5

post on the right channel PWB.

– Connect the NC terminals – T51 primary windings not used for 120 V operation. Connect

the following wires to any of the available NC terminals on the right channel PWB:

•

Blue/yellow

•

Brown/yellow

•

Black/red

•

White/black

– Connect the ground wire from power transformer T51 to the available ground lug on the

rear corner of the left channel PWB. Do not solder.

Double-check the connections from the power transformer to the three PWB.

5.6.7.5

Choke Leads

In the following steps, trim the lead lengths so the wires will comfortably reach their respective

terminals. After each terminal is attached to a lead, gently pull on the wire and terminal to make

sure a good crimp has been made.

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды