WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 6

Страница: 6 / 194

WhitakerAudio

•

Noise 70 dB below rated output (unweighted)

•

Frequency response ±1 dB 10 Hz to 50 kHz at typical listening level (5 W)

•

Harmonic distortion 0.75% or less at 5 W

•

Intermodulation distortion 1.5% or less at 5 W

•

Power supply for separate preamplifier included

•

Line input impedance 100 k

, 1 V rms nominal for full power output

•

Conservatively rated components used throughout

•

Soft-start power supply to extend component life

•

Adjustable output tube bias for optimal performance

•

Automatic circuit protection built in, including auto-off feature

•

Power requirements: 120 V ac, 60 Hz, 120 W nominal

•

Physical dimensions: 19-in wide by 16-in deep by 7-in high. Note that the depth

specification does not include back panel cables

•

Weight approximately 40 lbs

The amplifier is built around three main printed wiring boards (PWBs) and five special-

purpose boards, engineered for top performance. Component placement and board traces have

been engineered to minimize hum and noise. The boards feature a unique mounting technique for

the vacuum tubes that keeps heat away from the PWB and minimizes hum in the amplifier. The

PWBs are designed to reduce off-board connections, thereby simplifying layout and providing for

controlled characteristics from one unit to the next. The PWBs include top and bottom solder

masks and top-side silk-screened legends.

The power supply uses a vacuum tube rectifier feeding a choke and followed by a high-

capacity bank of filter capacitors. The active circuits of the power amplifier utilize a 6U8A input

amplifier and phase splitter. The power output stage is built around a matched pair of 6973 beam

power tubes. Top-quality Hammond transformers are used throughout. The transformers are

conservatively rated, providing wide operating margins.

The output circuit utilizes a screen-tap configuration to optimize sonic performance. Generous

power supply filtering ensures a rock-steady reserve for the output stage.

Adjustable bias to the push-pull output tubes provides a wide range of operating points,

allowing users to find a good middle point between top performance and long tube life.

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды