WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 95

Страница: 95 / 194

20 W Stereo Audio Amplifier

should be positioned between the cable clamp and the lockwasher/nut. Orient the cable

clamps as shown in Figure 5.11.

– Find the three cable clamps that are also used to mount the acrylic trim piece. There are

three sets of hardware. Install using the hardware provided. Orient the cable clamps as

shown in Figure 5.11. The proper order of hardware is as follows (from bottom of chassis

to top): screw head (6-32 x 3/8) / flat washer / cable clamp / chassis / lockwasher / standoff

/ chrome spacer / flat washer / screw head (6-32 x 3/4). The acrylic cover will be installed

later.

– Examine FL51, the AC line filter. Note there are two chassis mounting tabs. One tab also

serves as a standoff for the acrylic cover. Note also one end of the device is marked “line.”

This end should face the rear panel.

– Secure the rear-facing end of FL51 using the #6 hardware provided. Include a ground lug

between the mounting tab and the nut on the Line side. Note that the mounting tab may be

notched to permit easier assembly. With a notch in the mounting tab, the screw / ground

Figure 5.10

Back panel with components installed.

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды