Weidmuller UR20 Series Скачать руководство пользователя страница 21

Страница: 21 / 58

5 Assembly and installation

| Connecting the IO-Link device

Manual Communication module UR20-4COM-IO-LINK

2547720000/03/09.2019

WARNING

Explosion risk!

During installation work, sparks can form and

surfaces may become excessively hot

▶

Before starting any work, make sure that

there is not a potentially explosive atmos-

phere!

▶

For applications in explosive risk zones,

observe the installation and construction

requirements of EN 60079-15 and coun

try-specific regulations.

WARNING

Dangerous contact voltage!

▶

Carry out assembly and wiring work only

when the power supply disconnected.

▶

Make sure that the place of installation

has been disconnected from the power

supply!

ATTENTION

The product can be destroyed by elec-

trostatic discharge!

u-remote products can be destroyed by elec-

trostatic discharge.

▶

Please make sure that persons and work

equipment are adequately earthed!

▶

In addition, always refer to the complete doc-

umentation in the

u-remote IP20 manual.

▶

Carry out all work during the installation/removal and

replacement of components as described in the u-remote

manual.

5.1 Connecting the IO-Link device

ATTENTION

The module can be destroyed!

The voltage between C/Q and L- must not be greater that

the voltage between L+ and L-.

▶

Only connect the devices as shown.

Use unshielded cables of maximum 20 m length

to connect IO-Link devices.

Connecting IO-Link device for class A port

85&20,2/,1.

,2/LQNGHYLFH

Connecting IO-Link device for class A port (DI connection optional)

▶

Connect the IO-Link device as shown in the figure.

The use of the additional digital input at the DI

connection is optional. You can use this digital

input, e.g. if the IO-Link device provides an

additional switching signal.

5 Assembly and installation

Содержание UR20 Series



























































Результаты поиска

Содержание UR20 Series

Отзывы:

Похожие инструкции для UR20 Series

Бренды по названию

Популярные бренды

Weidmuller UR20 Series, Руководство пользователя

Результаты поиска

Содержание UR20 Series

Отзывы:

Похожие инструкции для UR20 Series

Бренды по названию

Популярные бренды