WAGO I/O SYSTEM 750 Скачать руководство пользователя

Страница: 232 / 260

232 Appendix

WAGO I/O System 750

750-8210/040-000 PFC200; G2; 4ETH; XTR

Manual

Version 1.7.0, valid from FW Version 04.01.10(23)

15.2.1.4.5

“Configuration of User Filter” Page

he “Configuration of User Filter” page displays the settings for custom firewall

filters.

“User filter” Group

Each configured filter has its own area in the display.

Table 137

: WBM “Configuration of User Filter” Page – “User Filter” Group

Parameters

Meaning

Policy

This displays whether the network participant is
permitted or excluded by the filter.

Source IP address

The source IP address for the respective filter is
displayed.

Source Netmask

This displays the source netmask for the respective
filter.

Source Port

The source port number for the respective filter is
displayed.

Destination IP address

The destination IP address for the respective filter is
displayed.

Destination Netmask

The destination netmask for the respective filter is
displayed.

Destination Port

The destination port number for the respective filter
is displayed.

Protocol

The permitted protocols for the respective filter is
displayed.

Input interface

The permitted interfaces for the respective filter are
displayed.

Add new user filter

You can create up to 10 filters.
You only have to enter values in the fields that are to
be set for the filter. At least one value must be
entered, all other fields can remain empty.

Policy

Select here whether the network devices is to be
allowed or excluded by the filter.

Allow

The network device is permitted.

Drop

The network device is excluded.

Source IP address

Enter here the source IP address for the new filter.

Source netmask

Enter here the source network mask for the new
filter.

Source port

Enter here the source port address for the new filter.

Destination IP address

Enter here the destination IP address for the new
filter.

Destination subnet mask

Enter here the destination network mask for the new
filter.

Destination port

Enter here the destination port address for the new
filter.

Содержание I/O SYSTEM 750





































































































































































































































































Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды

WAGO I/O SYSTEM 750, Руководство пользователя

Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды