WAGO I/O SYSTEM 750 Скачать руководство пользователя | Manualshive

Страница: 231 / 260

background image

WAGO I/O System 750

Appendix 231

750-8210/040-000 PFC200; G2; 4ETH; XTR

Manual

Version 1.7.0, valid from FW Version 04.01.10(23)

“MAC address filter state Bridge <n>” Group

A separate group is displayed for each configured bridge.

Table 135: WBM

“Configuration of MAC Address Filter” Page – “MAC address filter state Bridge <n>”

Group

Parameter

Explanation

Filter enabled

Enable or disable here the MAC address filter for the
specific bridge.
This setting is independent of the “Firewall enabled
entirely” setting on the General Firewall
Configuration page.

Click the

[Submit]

button to apply the change. The change takes effect

immediately.

“MAC address filter whitelist” Group

Each list entry has its own area in the display.

Table 136

: WBM “Configuration of MAC Address Filter” Page – “MAC address filter whitelist” Group

Parameters

Explanation

Description

Description of the devices or areas that can be
enabled by activating the filter when the firewall is
generally enabled.
The description is only visible for entries initially
available in the factory default settings.

MAC address

Displays the MAC address of the relevant list entry.

MAC mask

This displays the MAC mask of the relevant list
entry.

Filter enabled

Enable or disable the filter for the relevant list entry.

Add filter to whitelist

Create a new list entry.

MAC address

Enter here the MAC address for a new list entry.
You can enter 10 filters.

MAC mask

Enter the MAC mask for the new list entry.

Filter enabled

Enable or disable the filter for the new list entry.

Click the

[Submit]

button to apply the change. The change takes effect

immediately.

Click the appropriate

[Delete]

button to remove an existing list entry. The change

takes effect immediately.

Click

[Add]

to accept a new list entry. You can enter 10 filters. The change takes

effect immediately.

«
...
229
230
231
232
233
...
»

Содержание I/O SYSTEM 750





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O SYSTEM 750

Бренд: CAME Страницы: 12

PROFINET BNI PNT-508-055-P067

Бренд: Balluff Страницы: 84

Бренд: ICP DAS USA Страницы: 7

Бренд: ICP DAS USA Страницы: 28

I-2533CS Series

Бренд: ICP DAS USA Страницы: 8

Pure Link 1300 Series

Бренд: lancer Страницы: 20

Бренд: FARFISA INTERCOMS Страницы: 36

Бренд: Uniden Страницы: 28

Бренд: S.E.M. Страницы: 6

Chorus ANTAS GW19061

Бренд: Gewiss Страницы: 148

PAC iEVO Series

Бренд: Stanley Страницы: 2

Бренд: K-Systems Страницы: 9

MIGHTY MULE MM136

Бренд: Nortek Security & Control Страницы: 11

Бренд: Ravaglioli Страницы: 102

Бренд: Bame Страницы: 12

iNELS Air AirIM-100S

Бренд: Elko Страницы: 8

Бренд: Daewoo Страницы: 44

Бренд: Automated Logic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды