WAGO I/O SYSTEM 750 Скачать руководство пользователя

Страница: 195 / 260

WAGO I/O System 750

Appendix 195

750-8210/040-000 PFC200; G2; 4ETH; XTR

Manual

Version 1.7.0, valid from FW Version 04.01.10(23)

15.2.1.2.11

“Active System” Page

The settings for specifying the partition from which the system is started are
shown on the “Active System” page.

“Boot Device” Group

Table 92

: WBM “Active System” Page – “Boot Device” Group

Parameter

Explanation

Boot Device

The storage medium from which the device was
booted is displayed here.

“System <n> (Internal Flash)” Groups

Table 93

: WBM “Active System” Page – “System <n> (Internal Flash)” Group

Parameter

Explanation

Active

This shows whether the system is active.

Configured

This shows whether the system should be active
after the next reboot.

State

The system status is displayed here.

good

The system is valid and can be used.

bad

The system is not valid and cannot be
used.

Click the respective

[Activate]

button to start the required system at the next

reboot.

Provide a bootable system!

A functional firmware backup must be available on the boot system!

Содержание I/O SYSTEM 750





































































































































































































































































Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды

WAGO I/O SYSTEM 750, Руководство пользователя

Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды