WAGO I/O SYSTEM 750 Скачать руководство пользователя | Manualshive

Страница: 207 / 260

background image

WAGO I/O System 750

Appendix 207

750-8210/040-000 PFC200; G2; 4ETH; XTR

Manual

Version 1.7.0, valid from FW Version 04.01.10(23)

Table 109

: WBM “Configuration of Connection <n>” Page – “Configuration” Group

Parameter

Explanation

Certification file

Enter the path here to the file encoded in PEM
format that is used for cloud service authentication.

Key file

Enter the path to the file encoded in PEM format that
contains the private key for cloud service
authentication.

Use websockets

Here, you can specify whether the connection to the
cloud platform is to be set up using the Websocket
protocol via Port 443.
If this checkbox is not selected, the connection to
the cloud platform is set up using the MQTT protocol
via Port 8883.

Proxy Type

Select which type of proxy should be used.

HTTP Proxy Host

Enter the host name or IP address of the proxy.

HTTP Proxy Port

Enter the port number of the proxy.

HTTP Proxy User

Enter the name of the proxy user.

HTTP Proxy Password

Enter the password for the proxy user.

Use compression

Here, you can set whether the data is to be
compressed using GZIP compression.

Data Protocol

Here you can select the data protocol.

Cache mode

Specify in which memory the cache for the data
telegrams should be created.
This selection field is only enabled if a correctly
formatted SD card is inserted (more information is
available in Application Note A500920).

Last Will

You can specify whether a last will message should
be enabled/disabled.

(Last Will) Topic

You can specify the topic under which the last will
messages should be sent.

(Last Will) Message

You can enter the message you wish to use as the
last will message.

(Last Will) QoS

You can specify the “Quality of Service” (QoS) of the
last will message.

(Last Will) Retain

Here, you can set whether the previous last-will
message sent under a topic from the broker is to be
handled as a retained message.

Device info

Specify whether a device info message should be
generated that informs the cloud service of the basic
configuration of the controller (more information is
available in the Application Note A500920).

Device status

Specify whether device state messages should be
generated that inform the cloud service about
changes in the mode selector switch and the LEDs
(more information is available in the Application
Note A500920).

«
...
205
206
207
208
209
...
»

Содержание I/O SYSTEM 750





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O SYSTEM 750

Бренд: Safeline Страницы: 20

Бренд: TCS Страницы: 16

Бренд: Baier Страницы: 20

Chorus ANTAS GW19061

Бренд: Gewiss Страницы: 148

Box Design BT Box S2

Бренд: Pro-Ject Audio Systems Страницы: 6

Бренд: Viking Страницы: 11

Бренд: WaterGroup Страницы: 24

Бренд: GCAN Страницы: 12

Бренд: GL-Tech Страницы: 11

Бренд: WPG Страницы: 37

Бренд: JLG Страницы: 48

Бренд: Valcom Страницы: 4

Бренд: TrailKeg Страницы: 4

Бренд: Vestil Страницы: 14

Бренд: Cama Страницы: 18

750-1417/040-000

Бренд: WAGO Страницы: 58

Бренд: Tyco Страницы: 2

Бренд: Emerson Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды