WAGO I/O SYSTEM 750 Скачать руководство пользователя

Страница: 204 / 260

204 Appendix

WAGO I/O System 750

750-8210/040-000 PFC200; G2; 4ETH; XTR

Manual

Version 1.7.0, valid from FW Version 04.01.10(23)

15.2.1.2.19

“Configuration of DNS Server” Page

he “Configuration of DNS Server” page displays the DNS service settings.

“DNS Server” Group

Table 106

: WBM “Configuration of DNS Server” Page – “DNS Server” Group

Parameter

Explanation

Service active

You can enable/disable the DNS server service.

Mode

Select the operating mode of the DNS server.

Proxy

Requests are buffered to optimize
throughput.

Relay

All requests are routed directly.

Static Hosts

This displays the names for IP addresses. If no
assignment was defined, “No static hosts
configured” is displayed.

Add Static Host

You can add static IP addresses and host names
below.

IP Address

Enter a new static assignment,
e.g., “192.168.1.20:hostname”.
You can enter 10 assignments.

Hostname

Enter a host name.

Click the

[Submit]

button to apply the changes. The changes take effect

immediately.

To accept a new assignment click the

[Add]

button. The change takes effect

immediately.

Click

[Delete]

to delete an existing assignment. The change takes effect

immediately.

Содержание I/O SYSTEM 750





































































































































































































































































Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды

WAGO I/O SYSTEM 750, Руководство пользователя

Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды