WAGO I/O SYSTEM 750 страница 186 Скачать руководство пользователя

Страница: 186 / 260

186 Appendix

WAGO I/O System 750

750-8210/040-000 PFC200; G2; 4ETH; XTR

Manual

Version 1.7.0, valid from FW Version 04.01.10(23)

“Port-Forwarding” Group

Each entry has its own area in the display.

Table 84

: WBM “Routing” Page – “Port Forwarding” Group

Parameters

Explanation

Enabled

Specify whether port forwarding should be used.

Disabled

Port forwarding is not used.

Enabled

Port forwarding is used.

Interface

You can select the specified name of a network
interface. Alternatively, selecting “other” allows you
to specify any network interface name.

Port

Enter the port here on which the product receives
network data packets to be forwarded.

Protocol

You can select the protocol to be used for the port
forwarding. The options are TCP, UDP or both
protocols.

Destination Address

Specify the network address of the destination
device. This address replaces the original
destination address of the network data packet.

Destination Port

Specify the port number of the destination device.
This value replaces the original destination port of
the network data packet.

Click the

[Submit]

button to apply the changes. The changes take effect

immediately.

Click the

[Add]

button to add a new entry. The change takes effect immediately.

Click the

[Delete]

button to delete an existing entry. The change takes effect

immediately.

An entry is only transferred to the system if “Enabled” is enabled in the “General
Routing Configuration” group. This allows you to configure a default setting that is
not applied until the general switch-on.

Содержание I/O SYSTEM 750





































































































































































































































































Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды

WAGO I/O SYSTEM 750, Руководство пользователя

Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды