WAGO I/O SYSTEM 750 Скачать руководство пользователя

Страница: 162 / 260

162 Removal

WAGO I/O System 750

750-8210/040-000 PFC200; G2; 4ETH; XTR

Manual

Version 1.7.0, valid from FW Version 04.01.10(23)

Removal

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury. Do not touch the blade contacts.

13.1

Removing Devices

Do not work when devices are energized!

High voltage can cause electric shock or burns.
Switch off all power to the device prior to performing any installation, repair or
maintenance work.

13.1.1

Removing the Controller

Use a screwdriver blade to turn the locking disc until the nose of the locking
disc no longer engages behind the carrier rail.

Remove the controller from the assembly by pulling both release tabs.

Electrical connections for data or power contacts to adjacent I/O modules are
disconnected when removing the controller.

Figure 63: Release Tabs of Controller

Do not take the controller enclosure apart!

The enclosure sections are firmly joined. The feed-in section with the CAGE
CLAMP

connections cannot be separated from the other enclosure section.

Содержание I/O SYSTEM 750





































































































































































































































































Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды

WAGO I/O SYSTEM 750, Руководство пользователя

Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды