WAGO I/O SYSTEM 750 Скачать руководство пользователя

Страница: 154 / 260

154 Diagnostics

WAGO I/O System 750

750-8210/040-000 PFC200; G2; 4ETH; XTR

Manual

Version 1.7.0, valid from FW Version 04.01.10(23)

Table 63: Error Code 4, Explanation of Blink Codes and Procedures for Troubleshooting

Error

Argument

Cause

Solution

Maximum permissible
number of I/O modules
exceeded.

Switch off the power to the controller.

Reduce the number of I/O modules
to an acceptable value.

Switch the power back on.

Local bus disruption after
the n

process data

module.

Switch off the power to the controller.

Replace the (n+1)

process data

module.

Switch the power back on.

I/O modules that do not provide any data
are ignored (e.g., supply module without
diagnostics).

Table 64: Error Code 5, Explanation of Blink Codes and Procedures for Troubleshooting

Error

Argument

Cause

Solution

Switch off the power to the controller.

Replace the (n+1)

process data

module.

Switch the power back on.

I/O modules that do not provide any data
are ignored (e.g., supply module without
diagnostics).

Table 65: Error Code 7, Explanation of Blink Codes and Procedures for Troubleshooting

Error

Argument

Cause

Solution

First unsupported I/O
module in place of n.

Switch off the power to the controller.

Replace the nth I/O module
containing process data or reduce
the number of modules to the
number of n-1.

Switch the power back on.

Содержание I/O SYSTEM 750





































































































































































































































































Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды

WAGO I/O SYSTEM 750, Руководство пользователя

Результаты поиска

Содержание I/O SYSTEM 750

Отзывы:

Похожие инструкции для I/O SYSTEM 750

Бренды по названию

Популярные бренды