manualshive.com logo in svg

Wacker Neuson E3000, Руководство оператора

Поделиться
Скачать
Wacker Neuson E3000 Скачать руководство пользователя страница 52

 wc_tx001951gb.fm

52

Operation

E 3000

4.14

Positioning the Machine

CO Alarms

Because this machine produces carbon monoxide (CO), Wacker Neuson 
recommends that CO alarms be installed in all structures in close proximity to the 
machine. CO alarms provide an extra measure of protection against this poison 
that you cannot see or smell.

Install battery-operated CO alarms or plug-in CO alarms with battery backup, 
according to the manufacturer’s instructions. CO alarms should be certified to the 
requirements of the latest safety standards (UL 2034, IAS 6-96, or CSA 6.19.01). 
Test the CO alarm batteries monthly.

Requirements

Position the machine:

„

so that burner exhaust will not enter nearby structures.

„

so that the machine does not block traffic.

„

so that the machine is not close to any combustible material or flammable vapor.

„

so that all of the machine’s access doors/panels may be accessed.

„

so that HTF hoses do not pose tripping hazards, and so the HTF hoses cannot 
be damaged by machines or other equipment on the job site.

This procedure continues on the next page.

DANGER

Asphyxiation hazard.
Exhaust gas from the burner contains carbon monoxide, a deadly poison you 
cannot see or smell. Exposure to carbon monoxide can kill you in minutes.

f

Position the machine so that burner exhaust will not enter any nearby 
structures. 

WARNING

Fire hazard. Do not move the machine while it is running.

f

Shut down the machine before moving or repositioning it.

WARNING

Fire hazard. Machines positioned on a hill or an incline may slide, break away or 
roll over.

f

Do not position the machine on a hill or an incline.

WARNING

Explosion and fire hazard. Risk of severe injury or death.

f

Do not operate the machine near flammable vapors, fuels, or combustibles.

Содержание E3000























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды