manualshive.com logo in svg

Wacker Neuson E3000, Руководство оператора

Поделиться
Скачать
Wacker Neuson E3000 Скачать руководство пользователя страница 151

wc_tx001803gb.fm

151

E 3000

Maintenance

8.13

Storing the Machine

Short-term 
storage

1. Fill the HTF reservoir if it is low.

2. Stop the machine. See topic 

Shutting Down and Packing Up the Machine

. 

3. Remove and store any accessories. 

4. Allow the heater to cool sufficiently. 

5. Verify that all control switches are in the OFF position. 

6. Fill the fuel tank if it is low. Allow space in the fuel tank for fuel expansion. 

Long-term 
storage

1. Fill fuel tank with stabilized fuel and operate the burner for at least fifteen 

minutes to ensure circulation through entire fuel system. Any brand of fuel 
stabilizer is acceptable. 

2. Allow heater to cool sufficiently. Cover the chimney and the burner with plastic 

wrap or other waterproof material. This will prevent corrosive moisture build-up 
and blockages caused by animal nests.

3. Shut and lock all doors.

4. If the machine has a trailer, protect the trailer tires from direct sun light.

5. When removing from storage, the machine must be prepared for operation. See 

topic 

Preparing the Machine for Seasonal Operation

.

  

Содержание E3000























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды