Wacker Neuson E3000 Скачать руководство пользователя

Страница: 178 / 214

MSDS: Dowfrost™ HD 50

Product Name:

DOWFROST* HD 50 Heat Transfer Fluid, Dyed

Issue Date:

09/24/2010

Page

4 of 7

Physical and Chemical Properties

Physical State

Liquid.

Color

Yellow to green

Odor

Characteristic

Odor Threshold

No test data available

Flash Point - Closed Cup

Not applicable, Water boils off

Flammability (solid, gas)

Not applicable to liquids

Flammable Limits In Air

Lower

: 2.6 %(V)

Literature

Propylene glycol.

Upper

: 12.5 %(V)

Literature

Propylene glycol.

Autoignition Temperature

371 °C (700 °F)

Literature

Propylene glycol.

Vapor Pressure

15.5 mmHg @ 20 °C

Literature

Boiling Point (760 mmHg)

104 °C (219 °F)

Literature

Vapor Density (air = 1)

>1.0

Literature

Specific Gravity (H2O = 1)

1.06 20 °C/20 °C

Literature

Freezing Point

-33.8 °C (-28.8 °F)

Literature

Melting Point

Not applicable to liquids

Solubility in water (by
weight)

100 %

Literature

9.5

Literature

Decomposition
Temperature

No test data available

Partition coefficient, n-
octanol/water (log Pow)

No data available for this product.

Evaporation Rate (Butyl
Acetate = 1)

<0.5

Estimated.

Kinematic Viscosity

6.3 cSt

Literature

10.

Stability and Reactivity

Stability/Instability

Thermally stable at recommended temperatures and pressures.

Conditions to Avoid:

Some components of this product can decompose at elevated temperatures.

Generation of gas during decomposition can cause pressure in closed systems.

Incompatible Materials:

Avoid contact with: Strong acids. Strong bases. Strong oxidizers.

Hazardous Polymerization

Will not occur.

Thermal Decomposition

Decomposition products depend upon temperature, air supply and the presence of other materials.

11. Toxicological

Information

Acute Toxicity

Ingestion

For the major component(s): Propylene glycol. LD50, Rat > 20,000 mg/kg

Dermal

For the major component(s): Propylene glycol. LD50, Rabbit > 20,000 mg/kg

Inhalation

For the major component(s): No deaths occurred following exposure to a saturated atmosphere.

LC50, 8 h, Vapor

Rat 4.1 mg/l

Содержание E3000























































































































































































































Результаты поиска

Содержание E3000

Отзывы:

Похожие инструкции для E3000

Бренды по названию

Популярные бренды

Wacker Neuson E3000, Руководство оператора

Результаты поиска

Содержание E3000

Отзывы:

Похожие инструкции для E3000

Бренды по названию

Популярные бренды