manualshive.com logo in svg

Wacker Neuson E3000, Руководство оператора

Поделиться
Скачать
Wacker Neuson E3000 Скачать руководство пользователя страница 32

 ghi_tx001160gb.fm

32

Lifting and Transporting

E 3000

3.3

Transporting the Machine on a Truck or Trailer

Requirements

„

Machine stopped. See topic 

Stopping the Machine

. 

„

All doors and access covers closed and secured.

NOTICE: 

Do not run chains or straps across painted surfaces. Chains or straps 

may damage your machine.

Move the 
machine

1. Move the machine onto the flat bed using properly rated ramps or docks.

NOTICE: 

The flat bed must be at least 98 inches wide.

Support the 
tongue

2. Raise the tongue using the trailer jack

 (a)

.  

3. Install the tongue support 

(b)

 using two 5/8 inch bolts.

NOTICE: 

If the supplied tongue support is missing, use any mechanism capable of 

supporting the tongue weight.

4. Lower the tongue and retract the trailer jack 

(a)

 at least two inches from the 

surface of the truck bed. 

This procedure continues on the next page.

WARNING

Crushing hazard. Improperly securing the machine can lead to a crushing hazard.

f

Use only the designated tie-down points to secure the machine. 

Содержание E3000























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды