Wacker Neuson E3000 Скачать руководство пользователя страница 35

Страница: 35 / 214

ghi_tx001160gb.fm

E 3000

Lifting and Transporting

3.5

Towing the Machine

NOTICE:

The towing vehicle must be equipped with a Class III or above hitch.

Procedure

Perform the procedure below when towing the machine.

1. Read and follow the towing safety guidelines. See topic

Safety Guidelines for

Towing the Machine

2. Complete the shut-down procedures. See topic

Stopping and Packing Up the

Machine

3. Adjust the amount of fuel in the machine to approximately 70% capacity to avoid

fuel spillage.

4. Complete the Before Towing Checklist. See topic

Before Towing Checklist

5. Connect the machine to the towing vehicle.

6. Rotate the trailer jack to a horizontal position.

7. Tow the machine as needed.

WARNING

Risk of severe injury or death. Improperly torqued lug nuts can lead to loss of
wheels. Loss of wheels can cause an accident, severe injury or death.

Tighten the lug nuts to the proper torque before towing the machine.

Содержание E3000























































































































































































































Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson E3000, Руководство оператора

Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды