manualshive.com logo in svg

Wacker Neuson E3000, Руководство оператора

Поделиться
Скачать
Wacker Neuson E3000 Скачать руководство пользователя страница 154

 wc_tx001803gb.fm

154

Maintenance

E 3000

8.16

Connecting and Maintaining the Battery

Battery 
connections

To connect the battery:

„

Connect the positive (+) battery cable to the battery.

„

Connect the negative (-) battery cable to the battery.

To disconnect the battery:

„

Stop the engine.

„

Place all electrical switches in the OFF position.

„

Disconnect the negative (-) battery cable from the battery.

„

Disconnect the positive (+) battery cable from the battery.

Maintaining 
the battery

„

Follow the battery manufacturer’s maintenance recommendations.

„

Keep battery terminals clean and connections tight.

„

When necessary, tighten the cables and grease the cable clamps with 

petroleum jelly.

„

Maintain the battery at full charge to improve cold weather starting. 

Precautions

Observe the following precautions to prevent serious damage to the electrical 
system.

„

Do not disconnect the battery while the machine is running.

„

Do not attempt to run the machine without a battery. 

„

Do not attempt to jump-start the machine.

„

In the event that the machine has a discharged battery, either replace the 

battery with a fully charged battery or charge the battery using an appropriate 
battery charger. See 

Technical Data 

for the equivalent battery specification.

„

Dispose of waste batteries in accordance with local environmental regulations.

  

WARNING

Explosion hazard. Batteries can emit explosive hydrogen gas. 

f

Keep all sparks and flames away from the battery. 

f

Do not short-circuit battery posts.

WARNING

Battery fluid is poisonous and corrosive. 

f

In the event of ingestion or contact with skin or eyes, seek medical attention 
immediately.

Содержание E3000























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды