manualshive.com logo in svg

Wacker Neuson E3000, Руководство оператора

Поделиться
Скачать
Wacker Neuson E3000 Скачать руководство пользователя страница 171

wc_tx002271gb.fm

171

E 3000

Troubleshooting

 

10.2

Troubleshooting the Oil Burner

  

Problem / Symptom

Reason

Remedy

The burner does not start.

Improper switch position or 
protective function action.

Verify that the breaker is 
ON. Verify that the HTF 
level is within range and low 
level shutdown device is 
reset (low level indicator 
light must be OFF).

The over-temperature limit 
has tripped.

Allow the burner to cool.

The burner primary control 
is in lockout mode.

Reset the burner control.

The burner starts; the flame 
does not ignite.

There is no fuel.

Fill fuel tank.

The burner nozzle is dam-
aged or worn.

Replace the burner nozzle.

The electrodes are defec-
tive.

Replace the electrodes.

The cadmium cell is mal-
functioning.

Replace the cadmium cell.

The burner primary control 
is malfunctioning.

Replace the burner primary 
control.

The burner starts and the 
flame ignites, but the unit 
locks out.

The fuel pressure is set 
incorrectly.

Adjust the fuel pressure.

The burner nozzle is dam-
aged or worn.

Replace the burner nozzle.

The air damper is set incor-
rectly.

Adjust the air damper.

The cadmium cell is mal-
functioning.

Replace the cadmium cell.

The burner primary control 
is malfunctioning.

Replace the burner primary 
control.

Combustion is poor or 
noisy.

There is a lack of fresh air 
to burner.

Ensure there is an ade-
quate air supply.

Содержание E3000























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды