manualshive.com logo in svg

Wacker Neuson E3000, Руководство оператора

Поделиться
Скачать
Wacker Neuson E3000 Скачать руководство пользователя страница 118

 wc_tx001802gb.fm

118

Burner Setup—Oil

E 3000

6.6

Adjusting the Air Settings

Factory 
settings

„

Air band: 0

„

Air shutter:

 6.5

Note: 

These settings are initial settings only. Adjust the air settings as necessary to 

obtain the proper smoke spot and combustion analysis values.

Background

There are two parts to adjusting the air setting: 1) air band; and 2) air shutter. 
Adjust the air band to make large adjustments. Adjust the air shutter to make small 
adjustments.

Effects

The air setting has the following effects on combustion.

„

Higher O

2

 percentage (excess air settings) lowers soot production but raises 

stack temperature and reduces efficiency: lean mixture.

„

Lower O

2

 percentage (inadequate air settings) increases efficiency and lowers 

stack temperature but may cause soot build-up: rich mixture.

Procedure

Follow the procedure below to adjust the air settings.

1. Initial setting of the air damper should be performed with the machine shut 

down.

2. Loosen the air band locking screw 

(a)

 and the air shutter locking screw 

(b)

.

3. Using the band position pointer 

(c) 

to determine position, move the air band to a 

higher number to increase air volume. Turn it to a lower number to decrease air 
volume. 

4. Using the shutter position pointer 

(d) 

to determine position, move the air shutter 

to a higher number on the shutter position pointer to increase air volume. Turn it 
to a lower number to decrease air volume.

5. After the air settings have been made, tighten the band-locking screw 

(a)

 and 

the shutter-locking screw 

(b)

.

Result

The air settings have now been adjusted.

wc_gr008525

c

d

a

b

Содержание E3000























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды